IC698CPE040 RX7i cpu通过编程软件进行编程和配置 IC698CPE040-JP

RX7i cpu通过编程软件进行编程和配置，以执行机器，过程和物料处理系统的实时控制。CPU通过机架式背板与I/O和智能选件模块通信，采用VME64标准格式。它通过嵌入式以太网端口或使用SNP Slave协议的串行端口与程序员和HMI设备通信。
CPE030: 600MHz Pentium-M微处理器，64mb用户内存和64mb用户闪存
CPE040: 1800MHz Pentium-M微处理器，64mb用户内存和64mb用户闪存
特性
包含64mb的电池支持的用户存储器和非易失性闪存用户存储器，用于存储用户数据(程序、配置、寄存器数据和符号变量)。
▪通过引用表%W访问大容量内存。
▪可配置的数据和程序存储器。
掌握梯形图、C语言、结构化文本和功能框图编程。
自动定位符号变量，可以使用任意数量的用户内存。
▪支持系列90-70离散和模拟I/O，通信和其他模块。有关支持的模块列表，请参阅PACSystems RX7i安装手册GFK-2223。
▪支持系列90-70支持的所有VME模块。
▪Rx7i数据监控网络。允许总共多达16个web服务器和FTP连接。
▪多达512个程序块。块的最大大小为128KB。
▪测试编辑模式，允许您轻松地测试修改运行的程序。
-字位引用
▪电池供电的日历时钟。
▪CPU和模块固件通过Winloader通过CPU的RS-232或RS-485串口升级。
▪三个隔离的串行端口:一个RS-485串行端口，一个RS-232串行端口，和一个RS-232以太站管理器串行端口。
内置以太网接口:
使用以太网全局数据(EGD)交换数据
TCP/IP通信服务使用SRTP
支持SRTP通道、Modbus/TCP Server和Modbus/TCP Client
完整的编程和配置服务
综合工位管理和诊断工具
两个全双工10BaseT/100BaseT/TX (RJ-45连接器)端口，带有内部网络交换机，提供自动协商网络速度、双工模式和交叉检测。
●用户可配置冗余IP地址
在以太网上同步到SNTP时间服务器(与5.00及以上版本的CPU一起使用)。

IC698CPE040-JP

The RX7i CPUs are programmed and configured by the programming software to perform real time control of machines, processes, and material handling systems. The CPU communicates with I/O and smart option modules over a rack-mounted backplane using the VME64 Standard format. It communicates with the programmer and HMI devices via the embedded Ethernet ports or a serial port using SNP Slave protocol.
CPE030: 600MHz Pentium-M microprocessor with 64 MB of user memory and 64 MB of user flash
CPE040: 1800MHz Pentium-M microprocessor with 64 MB of user memory and 64 MB of user flash
Features
▪ Contains 64 Mbytes each of battery-backed user memory and non-volatile flash user memory for user data (program, configuration, register data, and symbolic variable) storage.
▪ Access to bulk memory via reference table %W.
▪ Configurable data and program memory.
▪ Programming in Ladder Diagram, C, Structured Text, and Function Block Diagram.
▪ Auto-located Symbolic Variables that can use any amount of user memory.
▪ Support for Series 90-70 discrete and analog I/O, communications, and other modules. For a list of modules supported, refer to the PACSystems RX7i Installation Manual, GFK-2223.
▪ Support for all VME modules supported by Series 90-70.
▪ Rx7i data monitoring over the web. Allows a combined total of up to 16 web server and FTP connections.
▪ Up to 512 program blocks. Maximum size for a block is 128KB.
▪ Test Edit mode that allows you to easily test modifications to a running program.
▪ Bit-in-word referencing
▪ Battery-backed calendar clock.
▪ CPU and module firmware upgrades via Winloader through CPU’s RS-232 or RS-485 serial port.
▪ Three isolated serial ports: an RS-485 serial port, an RS-232 serial port, and an RS-232 Ethernet station manager serial port.
▪ An embedded Ethernet interface with:
 Data exchange using Ethernet Global Data (EGD)
 TCP/IP communication services using SRTP
 Support for SRTP Channels, Modbus/TCP Server, and Modbus/TCP Client
 Full programming and configuration services
 Comprehensive station management and diagnostic tools
 Two full-duplex 10BaseT/100BaseT/TX (RJ-45 Connector) ports with an internal network switch providing auto-negotiated network speed, duplex mode, and crossover detection.
 User-configurable Redundant IP address
 Time synchronization to SNTP time server on Ethernet network (when used with Release 5.00 or later CPU module).