产品详情
详情介绍:T7560B1024 霍尼韦尔excel5000开放式系统
将DWM安装在约54英寸的内墙上。(1.3 m)距离地板(或按照安装图纸上的规定),以便暴露在平均区域温度下。
不要将DWM安装在外墙、有水管的墙壁或靠近风管的地方。避免暴露在寄存器排出的空气或灯光、电器或太阳辐射的地方。
DWM配有端子座;所有现场接线都连接到这8个端子。
DWM必须安装在垂直位置,LCD显示在顶部。
使用适用于墙体材料的螺钉直接将底座安装在墙上(见图3)。
重要的
对于表2中列出的控制器,DWM只能通过终端5供电,并且必须安装表2中列出的SW版本或更高版本。
如果DWM通过端子5供电,Excel 10控制器必须配置为LCD_DISPLAY (LED输出连续ON)。
注:只有T7560B,C DWM(用于湿度传感器)才需要24vac电源。
或者,一个直流电压源5…15V可以连接到5号端子(见上面的重要说明)。
或者,直流电压源18…27V(例如,来自W7750 CVAHU的22 Vdc)可以连接到端子8。
在24vac时,DWM的用电量为<s:1> 0.2 VA。DWM不需要专用变压器。DWM可以从24vac电源电路中任何方便的位置获得电源。
24vac电源可以来自最近的控制器上的24vac电源端子或直接来自24vac变压器,以较近的为准。
当所有接线完成后,如图5所示,连接DWM的盖板。
解释:
此操作的目标是重置房间用户在wall模块上执行的那些覆盖。因此,例如在酒店和办公楼中,典型的要求是远程将墙模块设定点覆盖重置为零,并远程将墙模块风扇超速重置为“自动”。
注意:如果墙壁模块被房间用户设置为关闭,它不能被重置为自动。
在Excel 50控制器的情况下,可以通过向wallmodule的LED输入发送6伏(=“未占用”)来完成复位:
只要6V被发送到LED输入,墙模块将处于“未占用”状态。
本地设定值和/或风扇速度设置将被重置和禁用。
只要10v被发送到LED输入
墙模块将处于“已占用”状态。
本地设定值和/或风扇速度设置将被启用。在Excel 10控制器的情况下,这种重置可以通过从“已占用”切换到“未占用”来完成。这将发送特殊编码的Excel 10信号到wallmodule的LED输入。
“无人”的意思。
有效未占用(月亮持续显示),或覆盖未占用(月亮闪烁)。
Mount the DWM on an inside wall approximately 54 in. (1.3 m) from the floor (or as specified on the installation drawings) to allow exposure to the average zone temperature.
Do not mount the DWM on an outside wall, on a wall containing water pipes or near air ducts. Avoid locations that are exposed to discharge air from registers or radiation from lights, appliances, or the sun.
The DWM is furnished with a terminal block; all field wiring connections are made to these eight terminals.
The DWM must be mounted in vertical position with the LCD display to the top.
Mount the subbase directly on a wall (see Fig. 3) using the type of screws appropriate for the wall material.
IMPORTANT
In the case of those controllers listed in Table 2, the DWM can be powered only via terminal 5, and only if a SW version listed in Table 2 or higher is installed.
If the DWM is powered via terminal 5, the Excel 10 controller must be configured for LCD_DISPLAY (LED output continuously ON).
NOTE: The 24 Vac power supply is needed only with the T7560B,C DWM (for the humidity sensor).
Alternatively, a DC voltage source with 5…15 V can be connected to terminal 5 (see IMPORTANT note above).
Alternatively, a DC voltage source with 18…27 V (e.g., 22 Vdc from W7750 CVAHU) can be connected to terminal 8.
The DWM power usage is 0.2 VA at 24 Vac. The DWM does not require a dedicated transformer. The DWM can get power from any convenient location in the 24 Vac power circuit.
The 24 Vac power can come from the 24 Vac power terminals on the nearest controller or directly from a 24 Vac transformer, whichever is closer.
When all wiring is complete, attach the cover of the DWM as is shown in Fig. 5.
Explanation:
The goal of this action is to reset those overrides which aroom user has enacted at the wall module.Thus, in, e.g., hotels and office buildings, a typical require-ment is to remotely reset the wall module setpoint override tozero, and to remotely reset the wall module fan speedoverride to “Auto”.
NOTE: if the wall module has been set to OFF by the roomuser, it cannot be reset to auto.
In the case of Excel 50 controllers, this reset can be doneby sending 6 Volt (= “unoccupied”) to the LED input of the wallmodule:
As long as 6V is being sent to the LED inputthe wall module will be in “unoccupied”
the local setpoint and/or fan speed setting will be resetand disabled.
As long as 10v is being sent to the LED input
the wall module will be in “occupied”
the local setpoint and/or fan speed setting will be enabled.In the case of Excel 10 controllers, this reset can be doneby switching from “occupied” to “unoccupied”. This will send aspecially coded Excel 10 signal to the LED input of the wallmodule.
“Unoccupied” means.
Effective Unoccupied (moon on continuously), orOverride Unoccupied (moon flashing).
其他相近型号:T7560B1024 霍尼韦尔excel5000开放式系统
3500/42M 176449-02弯曲内华达轴振动模块516tx 336A4940DNP516TX GE A微处理器器件
316tx – 336a4940dnp516tx GE微控制器
Bently Nevada通信网关模块2mlr – cput HONEYWELL CPUHT总线功能
3500/92-03-01-00 Bently NEVATA振动监测模块
7264 ABB四通道SSI接口模块具有自动pxie -6556 NI自动工业控制模块
ABB压力传感器控制器pfcl201ce
数字输入模块mtl BPHM64 Eaton安全栅格底板
3500/50 133388-02本特利内华达转速表监测模块4通道1794- if4ixt艾伦布拉德利Flex I/O 1794系列输入模块
BENTLY NEVADA扩展轴向位置模块1734- im4 Allen Bradley POINT I/O 4点数字输入模块
3500/15塑料面板BENTLY NEVADA交流和直流电源1769-ECR Allen-Bradley右端盖(ECR)模块一起使用
X20CP1586贝加莱I/O系统线136188-02 Bently Nevada以太网/RS232 Modbus I/O模块的核心产品
IC698PSA350 GE大容量电源模块ai02j ABB模拟输入模块
VMIVME 3215000 GE计算机模块dssa165 ABB交流电源模块
基于201TI GE微处理器的电变送器pxie -1073 NI PXI机箱
3500/05-01-02-00-00-01 BENTLY系统机架f860 – ca霍尼韦尔系列C“现场总线接口模块
PM865K02 ABB控制器dssa165 ABB交流电源模块
3500/22-01-01-00 138607-01 BENTLY大小卡模块前后的暂态数据接口125840-02 BENTLY电源模块
is420ucshbh4a GE GE控制器模块通用电气125680-01 BENTLY位移检测模块
METSO模拟输入模块147663-01 BENTLY Communication模拟输出模块
D201376 METSO模拟输入模块125800-01 Bently Nevada关键相输入/输出模块
IS420UCSBH4A GE控制器模块制造140471-01 Bently Nevada开发I/O模块与内部终端
IS220PRTDH1A 336A4940CSP6 GE控制器模块3500/ 22m 138607-01 Bently检测器模块
A413139 PC板电路板模块组装metso 3500/94 145988-01弯曲显示模块
D201471美卓RT节点PC AP31 D200137个性模块3500/ 42m 176449-02弯曲内华达轴振动模块
A413188 PC板电路板模块总成metso 3500/92 136180-01 bent nevada通信网关模块
A413331 PC板电路板模块组装metso 136180-01本特利内华达州通信网关模块
85UVF1A-1QD Fireye集成火焰扫描仪,内置火焰继电器3500/92-03-01-00
516TX 336A4940DNP516TX GE A微处理器器件7264 ABB四通道SSI接口模块功能自动
516TX-336A4940DNP516TX GE微控制器mdb – 8e赛多瑞斯称重传感器
2mlr – cput HONEYWELL CPUHT总线功能3500/15 127610-01 Bently Nevada数字输入模块