TIS600-124-SIG TIS系列的开关电源

特性
◆用于din导轨安装的开关电源
◆6个输出电流为2、3、6、12、20和24 A的功率范围(24 VDC型号)
◆可选115/230 VAC输入
极低的纹波和噪声
◆EMI符合EN 61000-6-3和EN 61000-6-4
◆工作温度范围:-25℃~ +70℃
◆为系统操作提供内置功能:
RED: N+1系统的冗余模块，具有真正的电流共享
SIG:信号模块，具有交流断电，电源良好信号和外部开/关控制
UDS: DC-UPS模块，用于不间断蓄电池备电系统
◆全球安全认证，包括I类，2类位置
◆易于卡扣式安装在din导轨或底盘上
◆3年产品保修

TIS系列的开关电源专为工业过程控制系统和机床的应用而设计。卓越的规格和对电气干扰的高抗扰性保证了在崎岖的工业环境中敏感负载的可靠电源。借助可选功能模块，可以用标准模型轻松实现系统应用的特定需求。通过UDS模块，供电系统可扩展为具有电池自动备份功能的完美直流ups。在需要延时关闭系统的应用程序中，通常需要此功能。为了监测和控制电源，可以安装信号模块。
对于具有有功功率共享的并联操作，可提供冗余选项。
这种灵活性使TIS系列电源成为许多工业应用中具有成本效益的解决方案

有了这个选项，并行操作多达5个单位是可能的。去耦二极管和电流共享线允许建立真正的N +1冗余系统，所有单元的有源电流共享。该功能还包括报警继电器，以指示单个单元的故障。
此选项可用于TIS 150w, TIS 300w和TIS 600w型号。请注意:此选项不能与其他选项组合使用。

除了标准的供电功能，这些型号还包括一个专业的电池管理系统来充电和监控外部电池。在电源故障的情况下，电池自动切换，不中断直流输出。一旦主电源再次可用，电池关闭。备用时间仅受电池容量和负载的限制。充电电流和电压可根据电池类型调整至所需值。电源故障和低电池报警信号可通过两个独立的继电器触点。正常运行时，通过定时短时间加载蓄电池，监测蓄电池状态。如果单元电阻高，则有继电器报警。电池在任何操作条件下都得到充分保护。即使在备用电池运行时，电源也有短路保护，但出于安全考虑，电池应配备快熔保险丝。连接引脚7和引脚8可以激活电池模式。

Traco TIS600-124

Features
◆ Switch mode power supplies for DIN-rail mount
◆ 6 power ranges with 2, 3, 6, 12, 20 and 24 A output current (24 VDC models)
◆ Selectable 115/230 VAC input
◆ Very low ripple and noise
◆ EMI complies with EN 61000-6-3 and EN 61000-6-4
◆ Operating temp. range –25°C to +70°C
◆ For system operation available with built-in functions:
RED: Redundancy module for N+1 Systems with true current sharing
SIG: Signal module with AC-power- fail, power good signal and external On/Off control
UDS: DC-UPS module for uninter- ruptable battery backed-up power systems
◆ Worldwide safety approvals incl. class I, div. 2 location
◆ Easy snap-on mount on DIN-rails or chassis mount
◆ 3-year product warranty

The switching power supplies of the TIS series have been particularly designed for applications in industrial process control systems and with machine tools. Excellent specifications and high immunity against electrical disturbances guarantee reliable power for sensitive loads in rugged industrial environments. With the help of optional function modules specific requirements for system applications can be easily realized with a standard model. With the UDS module the power supplies can be extended to a perfect DC-UPS with automatic battery- backup. This function is very often required in applications where a time delayed shutdown of a system is necessary. To monitor and control the power supply a signal module can be installed.
For parallel operation with active power sharing a redundancy option is available.
This flexibility makes the TIS series power supplies a cost effective solution for many industrial applications

With this option a parallel operation of up to 5 units is possible. Decoupling diodes and current share lines allow to build true N +1 redundant systems with active current sharing for all units. This function also includes an alarm relay to signal a single unit failure.
This option is available for TIS 150 W, TIS 300 W and TIS 600 W models. Please note: This option cannot be combined with other options.

In addition to the standard power supply function, these models include a professional battery management system to charge and monitor an external battery. In the event of a power failure the battery is switched automatically and without any interruption to the DC output. Once mains power is available again, the battery is switched off. The backup time is limited only by battery capacity and load. Charge current and voltage can be adjusted to values as required by battery type. Power fail and low battery alarm signals are available via two independent relay contacts. During normal operation the battery status is monitored by periodically loading the battery for a short time. If a cell resistance is high, there is a relay alarm is available. The battery is fully protected under any operational conditions. The power supply is short circuit protected even in battery backup operation but, for safety reasons, the battery should be fitted with a fast blow fuse. Battery mode can be activated by interconnecting pin 7 and 8.